NSBB-006 JAV [Sangat panjang 948 menit! ] Dokumen Creampie SP penuh dengan wanita cantik! Festival seks mentah tanpa kulit bercinta pribadi yang terdiri dari 7 wanita cantik yang setuju dengan creampie! (An Mitsumi, Mao Watanabe, Mei Satsuki, Hikari Sena, Kasumi Tsukino, Megu Mio, Kana Yura) [Rekaman belum dipotong] Dokumen creampie NOSKINS 948 menit selesai... - Cuplikan Gratis dan Subtitle Bahasa Indonesia srt.

VOBB-010 Melihat kemajuan dengan tekun pasti akan meningkatkan keterampilan secara maksimal.

17 Mar 2023

VOTAN-036 Menikmati Kehangatan Bersama di Pemandian Bersama Yui Hatano

17 Mar 2023

VOTAN-039 Penyelesaian Kasus dengan Banya Nnn dan Juzu Hinami

17 Mar 2023

HMDNV-362 Studi Tentang Tren Kelahiran Bayi di Jepang dalam Konteks Sosial Modern

17 Mar 2023

HMDNV-576 Video Momen Intim Pasangan Muda Bocor ke Publik

17 Mar 2023

REFXD-001 Versi Remaster: Kisah Gadis Manis dan Janda Cantik di Apartemen, Yamaguchi Reiko

17 Mar 2023

REFXD-004 If you're trying to connect a sensor or a device to a microcontroller and it's not communicating properly, there are several things you can check to try and debug the issue: 1. **Power Supply:** Ensure that the sensor or device is receiving the correct voltage and current required. If the power supply is unable to meet these requirements, it may cause the device to malfunction. 2. **Check Connections:** Ensure that all connection cables are securely plugged in. Verify that there are no damaged or broken cables that may interfere with the operation of the device. 3. **Ground Connections:** Verify that the ground connections of the sensor, device and microcontroller are all connected to ensure proper operation. 4. **Digital Protocol:** Understand which protocol the device uses (I2C, SPI, UART, etc) and ensure that it is configured correctly on the microcontroller. Make sure that any required libraries or peripherals are enabled. 5. **Check SCL and SDA Pins (I2C Protocol):** If you're using the I2C protocol, confirm that the SCL and SDA pins are correctly connected to pull-up resistors on the microcontroller pins for the I2C or the sensor. Also ensure that no other components are interfering with the wiring. 6. **Check CS, MISO, MOSI, SCK Pins (SPI Protocol):** If using the SPI protocol, verify that all pins used (CS, MISO, MOS, SCK) are properly connected. 7. **Begin Serial Communication:** If you're using the UART protocol, confirm that the communication is set up exactly according to the manufacturer's instructions. 8. **Check Documentation:** Ensure that you go through the documentation carefully as there may be specific settings or configurations that need to be set up on the microcontroller. 9. **Read Sensor's Data Sheet:** Read through the datasheet of the sensor to ensure that you are appropriately configuring it. 10. **Use Logic Analyzer:** Use a logic analyzer to inspect and observe the communication between the sensor and microcontroller to identify any issues. 11. **Power Supply with Other Components:** If there are other components hooked up to the microcontroller, make sure that they operate independently and have their own power supply (if necessary) to prevent any interference. 12. Read and Understand Documentation Provided: Read and understand any datasheets, user manuals or other documentation provided for the device. This will help you ensure you're using the device correctly and allow you to resolve any potential issues with the sensor. By going through these points, you should be able to identify and resolve any issues with your microcontroller or device. '''

17 Mar 2023

REWSS-004 Rimasteran Versi Baru

17 Mar 2023

REWSS-008 [Versi Remaster AI] Himegal★Style Marin.

17 Mar 2023

REWSS-057 Permintaan untuk Versi Remaster dari Karya OGETSU 橘れもん

17 Mar 2023